Technical Support
Help you use GEEKTC products correctly and achieve optimal cooling performance
Usage Guides
Detailed steps and tips to make you a cooling expert
Thermal Paste Application
Steps
- 1Clean surfaces thoroughly with isopropyl alcohol on CPU and heatsink base
- 2Apply a pea-sized amount (about 5mm diameter) in the center of CPU
- 3Install cooler vertically without moving side to side
- 4Tighten screws in diagonal pattern gradually
- 5Test temperatures with monitoring software to confirm proper installation
Tips
- •More is not better - excessive paste can impair heat transfer
- •Once you place the cooler, don't lift it off to avoid air bubbles
- •New paste requires 24-48 hours break-in period for optimal performance
Thermal Gel Application Guide
Steps
- 1Surface preparation: Ensure surfaces are clean, dry, and free of contaminants
- 2Apply evenly using a spatula or professional dispensing equipment
- 3Thickness control: Recommended thickness 0.1-0.5mm
- 4Assembly: Complete assembly before gel cures
- 5Curing: Cure at room temperature for 24 hours or accelerate with heat
Tips
- •Gel is ideal for large or irregular surfaces
- •Repairable design for easy maintenance
- •Avoid contact with eyes and skin
Phase Change Material Instructions
Steps
- 1Cut to size according to chip dimensions
- 2Clean surfaces with alcohol
- 3Peel off protective films from both sides carefully
- 4Apply pad to chip and press gently to remove air
- 5Install heatsink and secure
Tips
- •Phase change material softens above specific temperature to fill micro-gaps
- •Requires 2-3 thermal cycles to reach optimal performance
- •Reusable but recommended to replace each time
Thermal Pads Application
Steps
- 1Clean surfaces to ensure they are dry and free of contaminants
- 2Measure gap and select appropriate pad thickness
- 3Cut to size as needed
- 4Peel off protective film from one or both sides carefully
- 5Apply pad to component and press gently to make it flat
- 6Install heatsink and secure
Tips
- •Self-adhesive, no additional fixation needed
- •Soft material can compress 10-30% for uneven surfaces
- •Reusable but recommended to replace for critical applications
- •Avoid scratching with sharp objects
Liquid Metal Tutorial
Steps
- 1Safety first: Wear gloves and safety glasses
- 2Clean surfaces thoroughly with isopropyl alcohol on CPU and heatsink base
- 3Apply tiny amount with cotton swab
- 4Spread ultra-thin layer on CPU surface (thinner is better)
- 5Install cooler vertically and secure
- 6Clean any spills immediately with dry cotton swab
Important Notes
- ⚠️Extreme thermal conductivity for overclocking and high temperatures
- ⚠️Use minimal amount - less is more
- ⚠️DO NOT use with aluminum heatsinks (causes corrosion)
- ⚠️May dry out over time, replace every 1-2 years
- ⚠️Be careful of leakage when used in laptops
Precautions & Storage
Important safety information and proper storage methods
Safety Precautions
- • Power off before application for safety
- • Avoid contact with eyes - rinse immediately with water and seek medical attention if contact occurs
- • Keep out of reach of children
- • Wash hands after use, avoid contact with food
- • Wear gloves if you have chemical sensitivities
- • Do not use liquid metal with aluminum heatsinks
Storage & Shelf Life
- • Storage temperature: -10°C to 30°C
- • Avoid direct sunlight and high temperature environments
- • Unopened shelf life: 24 months
- • Use within 6 months after opening
- • Cap tightly after use to prevent drying
FAQ
- • Q: How often should I replace thermal paste? A: Check after 2-3 years, replace if temperatures rise significantly
- • Q: Can I mix different brands of paste? A: Not recommended - clean thoroughly and use single product
- • Q: What if paste dries out? A: Slight drying is normal, replace if fully cured
- • Q: Can I use on laptops? A: Yes, all products work on both laptops and desktops
Need More Help?
Explore additional resources and support channels